Page 4 of 4 FirstFirst ... 234
Results 31 to 40 of 40

Thread: General IAC Info & Ford PWM IAC Wiring

  1. #31
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,723

    Default

    It depends on how well the idle quality is tuned.
    A good idle will only fluctuate the Idle Spark control about +/ 2°-3°.
    A poor idle can fluctuate the Idle Spark control as much as +/ 8°-9°.
    http://forums.holley.com/showthread....e-Tuning-Notes (Read "Idle Spark Control Tuning".)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  2. #32

    Default

    So +/ 8°-9° spark timing is the maximum the Holley will use to control idle speed. The engine's previous Mercruiser PCM555 would use about four times that, is why I asked. Thank you.

  3. #33

    Default

    Can any one tell me the PID IAC control values used when "FAST", "MEDIUM" or "SLOW" is selected in Advanced Idle Control? Thanks, Bullshark.

  4. #34
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,723

    Default

    The Slow, Medium & Fast IAC PID/Blanking values are now listed in post #1.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  5. #35

    Default

    When using the Ford 2-wire IAC, should Advanced Idle Control be "5.0L Ford" or something else?

  6. #36
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,723

    Default

    Not necessarily. Select the setting that best fits your engine application.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  7. #37

    Default

    Are 18 gauge wires suitable for the Ford IAC motor, or can I use something smaller?

  8. #38
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,723

    Default

    Yes, 18 AWG is fine. Always refer to the Holley EFI Wiring Manual. You'll see the IAC motor wiring is 22 AWG.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  9. #39

    Default

    I did see that, but thought that was for the Holley IAC, wasn't sure if the Ford unit I will be using needed a larger size. Thanks.

  10. #40
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,723

    Default

    You're welcome, 18 AWG is fine.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Page 4 of 4 FirstFirst ... 234

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us