Results 1 to 4 of 4

Thread: 4L80E Manual Shift Issue At WOT

  1. #1

    Default 4L80E Manual Shift Issue At WOT

    Got the project out on the road for a quick test spin. When in drive, the transmission shifts fine. When in manual, it shifts right when I want it I'm at partial throttle. If I'm full throttle, or higher RPM, it wouldn't shift right away. It'd go about 400 more RPM. Is this a setting in the Holley Terminator or is this something mechanically wrong? (It's a 4L80E transmission with Trans Go shift kit/3000 converter behind a 5.3L LS.)

  2. #2

    Default

    This is fairly normal. The ECU can only command a shift, but the actual shift is carried out by the transmission. At higher RPM there's usually a delay. So make sure you set your WOT shift RPM accordingly, so you don't hit your rev limiter. Andrew

  3. #3
    Join Date
    Nov 2014
    Location
    Ont. Canada
    Posts
    1,703

    Default

    Datalog the event and you'll see what Andrew is talking about. My 4L60E takes about .7 seconds from the time the ECU commands the shift, and you actually see the RPM drop because of the shift.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,963

    Default

    Overlay the datalog onto your Config File, and pay special attention to the center paragraph in blue print:
    Originally Posted by Danny Cabral
    Quick Datalogger Information:
    Always provide data, not just symptoms. Is the AFR & ignition timing optimized? Overlay the datalog onto your Config File.
    Ensure the Target A/F Ratio table is properly programmed for your engine. Ensure the ECU is "Learning" (Learn Table LINK).
    Scroll through the datalog to the problem area. Then look exactly where this happens on the Base Fuel & Timing Tables. Scrutinize:
    RPM, MAP, MAT, TPS, CTS, IAC, Target AFR, AFR Left, CL Comp, Ignition Timing, Duty Cycle, Fuel Flow, Fuel Pressure & Battery.

    Using the Holley Terminator X EFI software (LINK), look at where the live cursor moves to during this occurrence,
    and manually tune that area of the Base Fuel Table (enrich or lean) & Base Timing Table (optimize ignition timing).


    I find the most helpful datalog function, is overlaying the datalog on your Config File.
    I'm in the habit of using the datalog Overlay feature every time I review a datalog.
    Click on "Datalog" (on the top Toolbar), "Activate Overlay", then "Open Data Log".
    You can literally "playback" a recorded event, and watch it as it happened on any screen.
    Minimize (shrink) the datalog window, and move it to the bottom of any Config File screen.
    Then click & scroll anywhere on the datalog, and watch it playback on your Config File (EFI software).
    http://documents.holley.com/techlibr...9r10543rev.pdf (Holley EFI Datalogger Instructions)
    https://forums.holley.com/showthread...s-amp-Datalogs (Datalog Information - Read "NOTES")
    https://www.youtube.com/watch?v=iqHO...C6FEA0BB99AF17 (How To Record & Email A Datalog)
    https://forums.holley.com/showthread...7531#post77531 (Closed Loop Datalog Tuning - Posts #2, #4 & #6)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us