Results 1 to 8 of 8

Thread: Fox body main harness.

  1. #1

    Default Fox body main harness.

    I got the factory computer out and the huge bundle of wires all the way over to the TFI. The bundle goes in behind the coil. Does it all get removed? Nothing going down the driver side inner fender well?

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,963

    Default

    This is how I installed it: https://forums.holley.com/showthread...464#post100464 (Related Ford 5.0L Fox Mustang - Holley HP/Dominator EFI Installation Post)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  3. #3

    Default

    Thanks for the help.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,963

    Default

    You're welcome.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  5. #5

    Default

    My question is about installing Holley HP in Fox body. Your post/writeup about installing required cutting factory harness, but retaining harness in place? Or cutting & removing? The Terminator X install by Holley says remove computer harness and just tie into a connector C216. Can the HP be installed the same? Or is it a different benefit to install HP the way you installed Dominator?

  6. #6
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,963

    Default

    Again, I did not remove the factory Ford EFI main harness. I only removed the two engine harnesses. Please read that post again.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  7. #7

    Default

    Yes, I'm asking can the HP be installed as the Terminator X install detailed? With removing the computer harness completely and tying into the C216 connector? I have a '93 with the 2.3L, if that makes a difference.

  8. #8
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,963

    Default

    Yes, it's very similar.
    https://www.holley.com/blog/post/how...xbody_mustang/ (Terminator X EFI System Installation Video - Fox Body Mustang)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us