C950 upgrade confusion, 550-604 or 554-113?

[Danny Cabral]

Yes, the Terminator EFI can use a crank trigger kit.

[SCP440]

The magnetic crank trigger? How is it connected? Is there a loom ready made to join it? What option would I tick?

[Danny Cabral]

You can run an MSD crank trigger kit with Holley's 554-118 Hall-Effect crank sensor.
Holley's 554-118 direct replacement Hall-Effect crank sensor (¾"-16 threaded sensor):
http://documents.holley.com/199r10633rev.pdf (Holley 554-118 Instructions)

Or you can run the Holley EFI 36-1 crank trigger kit (Hall-Effect sensor) for small block Fords:
https://www.holley.com/products/igni.../parts/556-115 (Holley EFI SBF 36-1 Crank Trigger Kit)
http://documents.holley.com/199r10923.pdf (Holley 556-115 36-1 Crank Trigger Kit Instructions)

The Hall-Effect crank & cam sensors are wired as shown in the Holley EFI Wiring Manual:
http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual - Figure 11/12, Page 20/21)
http://forums.holley.com/showthread....m-Sensor-Setup (Crank & Cam Sensor Setup)
http://forums.holley.com/showthread....ing-Holley-EFI (Ignition Timing Synchronization)

[SCP440]

Thanks, that sounds good. What option would I need to tick with this crank trigger?

[Danny Cabral]

Custom Ignition Parameters for MSD Flying Magnet 4x crank trigger & Holley 554-118 Crank Sensor:
Ignition Type ............. ― "Custom"
Crank Sensor Type ..... ― "1 Pulse/Fire" (← Holley 554-118 crank sensor LINK.)
Sensor Type .............. ― "Digital Falling" (← Hall-Effect sensor.)
Inductive Delay .......... ― "adjusted per application" (← Synchronization info.)
Ignition Reference Angle ― "50° or 60°" (← Crank sensor setup LINK.)
Cam Sensor Type ........ ― "Single Pulse" (← If sequentially injected or CNP ignition.)
Sensor Type .............. ― "Digital Falling" (← Cam sensor setup LINK.)
Output Setup Type ..... ― "Points Output" (← Loose white wire CDI box trigger.)
Dwell Time ................ ― "2.0 msec" (← Do not set this to 1.5 msec!)

[makemeknowit]

So this is actually an Avenger that I bought used, but I'll be using a laptop, so in essence it's HP. Is the Innovate LC-1 that was in play with the Commander 950 not needed with the Avenger/HP? I see the wideband connector is entirely different on the HP as compared to the Commander 950. What style of wideband O2 sensor is used on the HP? The brand new one I bought for the Commander 950 (along with extension) is money wasted I assume? I have no idea if the used sensor with the HP is any good.

[Danny Cabral]

You need to read the Holley EFI instruction manual. The Holley EFI system must use the Holley EFI WBO2 sensor. It's a proprietary wideband O2 sensor (LINK), specifically made & calibrated for Holley EFI. However, Holley's 534-199 4' long WBO2 extension harness is compatible.

Originally Posted by Danny Cabral EFI Software Help Information/Instructions: ‒ On the top Toolbar, click "Help" & "Contents". This opens all Help topics. ‒ When navigating the software, click "Help ?", drag it to any parameter and click again. ...This automatically opens the definitions for that specific parameter. ‒ Tuning information can be read by clicking the F1 key, when you're viewing any screen. http://documents.holley.com/techlibrary_199r10544.pdf (Holley EFI Help/Instructions Overview) http://documents.holley.com/techlibr...r10546rev1.pdf (Holley EFI Quick Start Guide) http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual & Diagrams) http://forums.holley.com/showthread....ents-Read-This (Initial Checks & Adjustments - Read Steps #1-#6!) Open the Holley EFI software "Help" Contents ("Help" drop down menu), and read "Step-By-Step Beginners Tuning". Ensure the EFI software is set to run as an "Administrator" (right click for Properties/Advanced). Set it and forget it.