Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23

Thread: Spark Plug Reading

  1. #11
    Join Date
    Feb 2020
    Location
    Augusta, Georgia
    Posts
    45

    Default

    Why, what’s wrong? LOL.

  2. #12
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    25,080

    Default

    Because the cylinder heads are the most significant ignition timing aspect (which is why Gaz64 asked too).
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  3. #13
    Join Date
    Feb 2020
    Location
    Augusta, Georgia
    Posts
    45

    Default

    OK, what does that change and what do I need to change?

  4. #14
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    25,080

    Default

    I'm not familiar with those heads, but if they're efficient combustion chambers, 31° seems fine (contact Canfield or dynamometer). However, the camshaft would probably like 20° of idle timing.

    Remember, the only thing this EFI system self-tunes, is the Base Fuel Table, via the Learn Table.
    You're responsible for everything else, especially the Target A/F Ratio Table & the Base Timing Table.
    A dynamometer is the only real way to determine the optimum ignition timing for your performance engine.
    Most people research it, or just "know" what their engine needs or likes. Especially if it's a popular engine.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  5. #15
    Join Date
    Feb 2020
    Location
    Augusta, Georgia
    Posts
    45

    Default

    OK cool. The only thing I did today was adjust the A/F Ratio to:
    14.2 Idle
    14.7 Cruise
    12.5 WOT

    I kept the timing as is:
    15° Idle
    36.6° Cruise
    31.3° WOT

    The car seems to respond pretty well even after I on beat it.

  6. #16
    Join Date
    Jan 2010
    Location
    Brisbane, Australia
    Posts
    1,700

    Default

    Sounds like you're fairly close. Now to optimize it, it would be wise to spend some time on a dyno, to get the timing closer to what the engine wants, at light throttle and under load.
    You might end up at 38-40° at light throttle. And you could also end up at 29-31° at WOT. Gary
    Regards, Gary

  7. #17
    Join Date
    Feb 2020
    Location
    Augusta, Georgia
    Posts
    45

    Default

    Sounds great. It'd be great if there was a dyno near me.

  8. #18
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    25,080

    Default

    Then at least contact Canfield heads to see what WOT timing they suggest for their cylinder heads (or drag strip testing).
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  9. #19
    Join Date
    Feb 2020
    Location
    Augusta, Georgia
    Posts
    45

    Default

    Canfield is no longer in business (they’ve been gone for years), but I think total timing @ WOT is 33°.

  10. #20
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    25,080

    Default

    Well then prove it with drag strip testing or a dynamometer tuning session.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

Page 2 of 3 FirstFirst 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us