Page 2 of 2 FirstFirst 12
Results 11 to 14 of 14

Thread: Enable timing and now no injectors.

  1. #11

    Default

    OK guys, I'm back. No, I have no cranking signal. I went through the wiring again, everything looks right, I double checked the firmware and it was V5.110. So I reinstalled and did the V5.130. Everything went well. Now when I turn the ignition on I can hear the injectors, but still no cranking signal. I tried changing to "Digital Falling", no change. Any ideas?

  2. #12
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    23,124

    Default

    Determine why there's no cranking RPM signal.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #13

    Default

    So everything I've read here says that the "I have to use the Holley 554-118 sensor". I ordered it, I'll try it and see if that works. Has anybody made the MSD sensor (MSD-8276) work?

  4. #14
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    23,124

    Default

    Quote Originally Posted by Vettster1 View Post
    So everything I've read here says that the "I have to use the Holley 554-118 sensor".
    Oh c'mon.

    I ordered it, I'll try it and see if that works.
    Yes, of course.

    Has anybody made the MSD sensor (MSD-8276) work?
    In my opinion, if a Holley EFI user isn't familiar with the Magnetic Ignition Type "Minimum Signal Voltage" &
    "Filtering" parameters (in System Parameters/Custom Ignition Parameters), then they have no business using
    VR/magnetic pickup type crank & cam sensors. This is the problem with using magnetic pickup type sensors,
    there's more tuning work/adjustment involved. Hall-Effect sensors are "set & forget", very easy to use.

    The more robust Hall-Effect sensors are preferred because they're not susceptible to EMI/RFI interference/noise,
    and their digital square-wave signal strength is consistent, regardless of RPM (unlike the VR magnetic sine-wave).
    Also, the VR magnetic pickup signal is weaker at cranking speeds.

    Another problem with using VR Magnetic sensors, is there's more tuning work. Hall-Effect is "set & forget".
    The VR Magnetic Sensor Type "Filtering" & "Minimum Signal Voltage" parameters need to be programmed.
    http://documents.holley.com/199r10676rev.pdf (Magnetic Crank/Cam Input Filtering Parameters, Page 2)
    http://forums.holley.com/showthread....4450#post54450 (Example: Wrong Magnetic Parameters, Post #25)

    Hall-Effect: 3-wire, square wave signal (digital), pulse generation
    VR Magnetic: 2-wire, sine wave signal (inductive), voltage generation
    http://www.electronicproducts.com/El...g_for_you.aspx (Hall-Effect vs VR Magnetic)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us