Results 1 to 6 of 6

Thread: 12-875 Filter/Regulator Fuel Pressure High

  1. #1

    Default 12-875 Filter/Regulator Fuel Pressure High

    I just installed the 12-875 Filter/Regulator hoping to solve the erratic ACDelco LS Filter regulator high pressure issue. The pressure is not stable and ranges from 62-70 psi and not the 59.5 as advertised. My system is the Holley Sniper EFI tank and -6AN lines 100%. Mounted by the tank with a 1 foot return and single line to the front. Tech Support suggested a filter and regulator setup, but I'd like it to be my last resort. Goal is still to only have a single line to the front. I'd appreciate any suggestions.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,745

    Default

    An EFI fuel system needs two filters:
    Before fuel pump - 100 micron pre-filter. (Or the OEM in-tank sock filter.)
    After fuel pump - 10 micron post-filter. (40 micron is for carburetion.)
    http://documents.holley.com/holleyfu...ems_chart1.pdf (Fuel System Selection Chart)
    http://documents.holley.com/flyer_ho...el_systems.pdf (Holley Fuel Systems Brochure)
    http://forums.holley.com/showthread....nts-amp-Clamps (Read 2nd quote box.)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  3. #3

    Default

    Thanks for the info. However, the Holley Sniper EFI tank supplies pump (Walbro 255 LPH with filter sock). I've used the correct sealants that was only on the NPT fittings to the tank hanger fittings, and there are no hose clamps on the fuel lines only the vent line. I've used Earl's Speed Flex SS hose and the correct fittings 100%. I believe the issue is the regulators used in the filter/regulator package. The 12-875 Filter/Regulator was not a cheap item and it does not perform as advertised at preset at 59.5 psi.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,745

    Default

    Quote Originally Posted by techdocwriter View Post
    I believe the issue is the regulators used in the filter/regulator package. The 12-875 Filter/Regulator was not a cheap item and it does not perform as advertised at preset at 59.5 psi.
    Contact Holley Tech Service (LINK).
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  5. #5

    Default

    I have the same filter/regulator setup in my Duster and it works just fine. Holds 60 psi from idle to WOT.

  6. #6
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,745

    Default

    Of course it does. There are many in use successfully. Also, the fuel pressure regulator can be replaced in that unit.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us