Results 1 to 5 of 5

Thread: Term X - engine stalls after coolant temp is hot.

  1. #1

    Default Term X - engine stalls after coolant temp is hot.

    Hello Fellow Terminator users. When I first start my 5.3L swap, engine starts & idles fine. Once it reaches warm/hot coolant temps the engine will not want to idle and it stalls, and it's hard to start it again. I tried uploading my Global File, but can't figure it out...darn it.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,702

    Default

    This is a copy & paste from one of my other posts:
    For further assistance, post your Global File and a short datalog of this occurrence for us to analyze.
    Also, review the datalog and inform us of exactly where in the datalog (time/seconds) the problem occurs.
    Datalog & Global Files must be linked to a document hosting website. I use Dropbox.com.
    Files can also be "zipped" (compressed zipped folder) & attached directly to a forum post.
    Your Global File is in the "Documents", "Holley", "HEFI V4", "Global Files" folder (.hefi file).
    Your Datalogs are in the "Documents", "Holley", "HEFI V4", "Datalogs" folder (.V4.dl file).
    Someone will analyze/troubleshoot the problem & offer advice. Also, ensure all this is right:
    http://forums.holley.com/showthread....ents-Read-This (Initial Checks & Adjustments - Read Steps #1-#6!)
    Quick Datalogger Information:
    Always provide data, not just symptoms. Is the AFR & ignition timing optimized? Overlay the datalog onto your Global File.
    Ensure the Target A/F Ratio table is properly programmed for your engine. Ensure the ECU is "Learning" (Learn Table LINK).
    Scroll through the datalog to the problem area. Then look exactly where this happens on the Base Fuel & Timing Tables. Scrutinize:
    RPM, MAP, MAT, TPS, CTS, IAC, Target AFR, AFR Left, CL Comp, Ignition Timing, Duty Cycle, Fuel Flow, Fuel Pressure & Battery.

    Using the Holley EFI software (LINK), look at where the live cursor moves to during this occurrence, and
    manually tune that area of the Base Fuel Table (enrich or lean) & Base Timing Table (optimize ignition timing).


    I find the most helpful datalog function, is overlaying the datalog on your Global File.
    I'm in the habit of using the datalog Overlay feature every time I review a datalog.
    Click on "Datalog" (on the top Toolbar), "Activate Overlay", then "Open Data Log".
    You can literally "playback" a recorded event, and watch it as it happened on any screen.
    Minimize (shrink) the datalog window, and move it to the bottom of any Global File screen.
    Then click & scroll anywhere on the datalog, and watch it playback on your Global File (EFI software).
    http://documents.holley.com/techlibr...9r10543rev.pdf (Holley EFI Datalogger Instructions)
    https://forums.holley.com/showthread...s-amp-Datalogs (Datalog & System Log Information - Read "NOTES")
    https://www.youtube.com/watch?v=iqHO...C6FEA0BB99AF17 (How To Record & Email A Datalog)
    https://forums.holley.com/showthread...7531#post77531 (Closed Loop Datalog Tuning - Posts #2, #4 & #6)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #3

    Default

    Thanks Danny. I'll try to get a datalog and post my current Global File.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,702

    Default

    You're welcome. Also, ensure all of this is correct: http://forums.holley.com/showthread....ents-Read-This (Initial Checks & Adjustments - Read Steps #1-#6!)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  5. #5

    Default

    @Danny Cabral. Here's the link for my tune and an idle datalog. I let it warm up and let it idle, once i give it gas to rev the engine, it then stalls. You can probably see where I revved it, the engine stalled: https://www.dropbox.com/sh/ayfm5oyq1...OvQNpudZa?dl=0

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us