Results 1 to 8 of 8

Thread: HP EFI LS System: Can I Use Outputs to Provide Gauges with Signal?

  1. #1

    Question HP EFI LS System: Can I Use Outputs to Provide Gauges with Signal?

    Hi. I'm wondering if it's possible to use output harness to output coolant temperature sensor signal from ECM to Auto Meter Water Temp gauge? If so, how would I do this? Please advise.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,684

    Default

    No, that's not possible.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #3

    Default

    Ah OK, that's too bad. On another note, how would I setup my fuel level sending unit to display on my Holley Pro Dash?

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,684

    Default

    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  5. #5

    Default

    Thanks, but all those threads seem to talk about the smaller dash with some type of harness. Just to clarify, should I wire into my ECU input/output harness or directly to the back of the Pro Dash? Is there a wiring kit for the Pro Dash to add the inputs?

  6. #6
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,684

    Default

    Quote Originally Posted by scottmmckinney View Post
    Thanks, but all those threads seem to talk about the smaller dash with some type of harness.
    The Pro Dash is programmed the same way (LINK).

    Just to clarify, should I wire into my ECU input/output harness or directly to the back of the Pro Dash? Is there a wiring kit for the Pro Dash to add the inputs?
    No it communicates with the ECU via CAN Bus.
    "Includes 34 Pin Wiring Harness contains Power, Ground and CAN Bus connections."
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  7. #7

    Default

    Thanks, I sent you an email. I appreciate your help!

  8. #8
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,684

    Default

    You're welcome. I don't have an LSx base calibration, but this is how it's programmed to create your Global File:
    http://forums.holley.com/showthread....ents-Read-This (Initial Checks & Adjustments - Read Steps #1-#6!)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us