Results 1 to 2 of 2

Thread: EFI HP & Digital Dash

  1. #1

    Default EFI HP & Digital Dash

    OK so first off I'm new to this obviously. I have a '94 Mustang with a 363" Turbo (Fun Street Car/Show Car), transmission is not electronically controlled. I'm going to run the HP EFI. A few questions I have that I've got confused on. I'm trying to retain factory A/C in this car, plus the electric fans (can be only one speed, that doesn't matter to me), also has a transbrake installed, will be running a boost controller, really thinking about Coil-On-Plug. So in short, I'd like to run as follows:
    A/C with fans.
    Boost Controller (Whatever is preferred.)
    Transbrake
    COP/CNP
    Trans Temp and maybe transmission cooler fan. Can use a separate controller if I had too.
    Speed Sensor for MPH
    Fuel Level
    I will also be using the Digital Dash, if I install temp gauges, etc., do they tie up inputs/outputs or can I wire them directly into the dash? Will all this work with the HP unit, or have I exceeded the inputs/outputs? Thanks for any advice!

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    21,430

    Default

    Quote Originally Posted by Mustang89 View Post
    A/C with fans.
    These are a lot of questions, please also search the forum.
    See Note #5: https://forums.holley.com/showthread...464#post100464 (Related Fox Mustang/Holley EFI Forum Post)
    https://forums.holley.com/showthread...Fan-Holley-EFI (Wiring an Electric Cooling Fan - Holley EFI)

    Boost Controller (Whatever is preferred.)
    http://forums.holley.com/showthread....SI-Equivalents (MAP kPa to Boost PSI Equivalents & Boost Control Information)

    Transbrake
    http://forums.holley.com/showthread....9883#post79883 (Transbrake Input Protection Module Information)

    COP/CNP
    If you already have or you're purchasing a new Holley non-LSx main harness:
    The Holley 558-307 CNP main harness is for Holley's Coil-On-Plug smart coils and LSx ignition coils.
    If using Holley's 556-112 CNP coils, Holley's 558-318 CNP coil sub-harness is also required (or Holley 556-128 CNP V8 Kit).
    For LSx ignition coils, the Holley 558-307 CNP main harness plugs right into the two GM 12579355 CNP sub-harnesses.
    IF you had an LSx main harness, you wouldn't need the Holley 558-307 CNP main harness or the 558-318 CNP coil sub-harness.
    https://www.holley.com/products/igni...nd_components/ (Holley EFI Coil-Near-Plug Ignition Components)
    https://www.holley.com/products/igni.../parts/556-128 (Holley EFI 556-128 Coil-Near-Plug Big Wire V8 Kit)
    https://www.holley.com/products/fuel.../parts/558-117 (Holley EFI 558-117 Universal MPFI Coil-Near-Plug Main Harness)
    https://www.holley.com/products/fuel.../parts/558-118 (Holley EFI 558-118 Ford Universal MPFI Coil-Near-Plug Main Harness)
    https://forums.holley.com/showthread...3038#post33038 (Detailed Crank Trigger & CNP/DIS Conversion Information & Reasoning)

    Trans Temp and maybe transmission cooler fan. Can use a separate controller if I had too.
    https://forums.holley.com/showthread...ture-ECU-Input (Transmission Temperature ECU Input)

    Speed Sensor for MPH
    http://forums.holley.com/showthread....ith-Holley-EFI (Installing A VSS Sensor)

    Fuel Level
    https://forums.holley.com/showthread...8310#post88310 (Related Forum Thread)

    I will also be using the Digital Dash, if I install temp gauges, etc., do they tie up inputs/outputs or can I wire them directly into the dash?
    The Digital Dash has its own I/O.
    http://documents.holley.com/199r10746rev1.pdf (Holley 553-106 Digital Dash Instruction Manual)
    http://documents.holley.com/199r10954rev2.pdf (Holley 558-432 Digital Dash I/O Adapter Instructions)

    Will all this work with the HP unit, or have I exceeded the inputs/outputs?
    The HP ECU only has four Inputs & four Outputs. If you need more than that, you'll need the Dominator ECU:
    http://documents.holley.com/techlibr...useanddiff.pdf (Holley HP & Dominator ECU Differences)
    With the Dominator EFI, everything is sold separately. Use Summit Racing's shopping cart for a total price.
    Most people find this document very helpful:
    http://documents.holley.com/efi_sele...chart62914.pdf (Holley HP & Dominator EFI Component Selection Guide)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: Dominator MPFI & DIS, A/C, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/X-pipe/shorty headers, 100HP progressive dry direct-port NOS, 160A 3G alternator, Optima Red battery, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us