Results 1 to 5 of 5

Thread: Exhaust Backfire

  1. #1

    Default Exhaust Backfire

    Looking for help on chasing an intermittent exhaust backfire at idle (haven't driven the car yet as this is a new install). I have a BBC with HP ECU. I'm virtually certain it is not an intake leak. Timing is 30° @ idle (both on timing light & ECU). Air/Fuel Ratio appears to be hitting targets (14.0 at idle). This is very intermittent. Any suggestions appreciated. Thanks.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    21,413

    Default

    Not enough information. What does your ignition system consist of? You'll have to record & review a short datalog (Overlay it onto your Global File) of this occurrence to determine what's wrong.

    Originally Posted by Danny Cabral
    Quick Datalogger Information:
    Always provide data, not just symptoms. Is the AFR & ignition timing optimized? Overlay the datalog onto your Global File.
    Ensure the Target A/F Ratio table is properly programmed for your engine. Ensure the ECU is "Learning" (Learn Table LINK).
    Scroll through the datalog to the problem area. Then look exactly where this happens on the Base Fuel & Timing Tables. Scrutinize:
    RPM, MAP, MAT, TPS, CTS, IAC, Target AFR, AFR Left, CL Comp, Ignition Timing, Duty Cycle, Fuel Flow, Fuel Pressure & Battery.

    Using the Holley EFI software (LINK), look at where the live cursor moves to during this occurrence, and
    manually tune that area of the Base Fuel Table (enrich or lean) & Base Timing Table (optimize ignition timing).


    I find the most helpful datalog function, is overlaying the datalog on your Global File.
    I'm in the habit of using the datalog Overlay feature every time I review a datalog.
    Click on "Datalog" (on the top Toolbar), "Activate Overlay", then "Open Data Log".
    You can literally "playback" a recorded event, and watch it as it happened on any screen.
    Minimize (shrink) the datalog window, and move it to the bottom of any Global File screen.
    Then click & scroll anywhere on the datalog, and watch it playback on your Global File (EFI software).
    http://documents.holley.com/techlibr...9r10543rev.pdf (Holley EFI Datalogger Instructions)
    https://forums.holley.com/showthread...s-amp-Datalogs (Datalog & System Log Information - Read "NOTES")
    https://www.youtube.com/watch?v=iqHO...C6FEA0BB99AF17 (How To Record & Email A Datalog)
    https://www.youtube.com/watch?v=q7OZUXLRS1Q (How To Record A System Log & Diagnose A No-Start Condition)
    https://forums.holley.com/showthread...7531#post77531 (Closed Loop Datalog Tuning - Posts #2, #4 & #6)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: Dominator MPFI & DIS, A/C, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/X-pipe/shorty headers, 100HP progressive dry direct-port NOS, 160A 3G alternator, Optima Red battery, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #3
    Join Date
    Aug 2018
    Location
    Russia
    Posts
    15

    Default

    If you use an MSD magnetic pickup, check polarity.

  4. #4
    Join Date
    Jan 2010
    Location
    Brisbane, Australia
    Posts
    1,332

    Default

    Have you checked rotor phasing with a modified cap with a hole drilled in it, and a timing light? Gary
    Regards, Gary

  5. #5
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    21,413

    Default

    To ensure the distributor's rotor-phasing is correct:
    http://documents.msdperformance.com/8644_tb.pdf (MSD Rotor-Phasing Document)
    MSD has a good video on why it's important:
    http://www.youtube.com/watch?v=aWMlNwGW0tM (MSD Tech Rotor-Phasing Video)

    For naturally aspirated engines, the rotor is usually phased halfway between minimum & maximum amount of timing advance used.
    For forced induction engines, the rotor is usually phased at maximum boost retard, because that's when cylinder pressure is the greatest.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: Dominator MPFI & DIS, A/C, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/X-pipe/shorty headers, 100HP progressive dry direct-port NOS, 160A 3G alternator, Optima Red battery, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us