Results 1 to 6 of 6

Thread: Problem with MAG pickup, and pressure pickups.

  1. #1
    Join Date
    Jun 2013
    Location
    Finland
    Posts
    2

    Default Problem with MAG pickup, and pressure pickups.

    Hello.

    We had problems with optic pickup, on logger it goes up and down, without any reasonable meaning. I think it messed up other curves too, because rear end curve was same looking.
    I fixed that optic cable and it was ok.
    After that, it worked couple rounds nicely, until problem came back.
    Now there aint no rpm, rear end information at lastest logging.
    Exhaust temps are ok.
    We are using oil press, pump press and blower press, nozzle press aint in use.
    But at that last logging, there was information of that nozzle press too.
    Is it possible that Loggers memory dont erase everything and it finds some old information and writes that?

    Sorry my bad english, I'm from Finland so its not my best spoken language.
    Hope you understand our problem.
    TAFC/TMFC
    Woodstock Racing.

  2. #2
    Join Date
    Sep 2007
    Location
    Rancho Santa Margarita, California
    Posts
    267

    Default Re: Problem with MAG pickup, and pressure pickups.

    Hello Mikkis,

    Are you waiting for the red light on the memory cartridge to flash on and off multiple times? Typically, the light will turn on and then go out while the data is transferring to the cartridge. Once this process is complete, the light will flash continuously.

    Is there any way you could email me some of you files to the address below? Let me know if I can be of further assistance.

    Sincerely,
    Todd Paton
    todd@racepak.com
    949-709-5555 ext. 1652

  3. #3
    Join Date
    Jun 2013
    Location
    Finland
    Posts
    2

    Default Re: Problem with MAG pickup, and pressure pickups.

    Thanks for response.

    Yes we did it like it should be done.
    Datas were ok few times, but last time it was ruined.

    I send it to you.
    TAFC/TMFC
    Woodstock Racing.

  4. #4
    Join Date
    Sep 2007
    Location
    Rancho Santa Margarita, California
    Posts
    267

    Default Re: Problem with MAG pickup, and pressure pickups.

    Mikkis,

    I am sending you an email about the runs. Looks like a memory cartridge problem. Do you have a spare?

    Sincerely,
    Todd Paton
    todd@racepak.com
    949-709-5555 ext. 1652

  5. #5

    Default Re: Problem with MAG pickup, and pressure pickups.

    Quote Originally Posted by Mikkis
    Hello.

    We had problems with optic pickup, on logger it goes up and down, without any reasonable meaning. I think it messed up other curves too, because rear end curve was same looking.
    I fixed that optic cable and it was ok.
    After that, it worked couple rounds nicely, until problem came back.
    Now there aint no rpm, rear end information at lastest logging.
    Exhaust temps are ok.
    We are using oil press, pump press and blower press, nozzle press aint in use.
    But at that last logging, there was information of that nozzle press too.
    Is it possible that Loggers memory dont erase everything and it finds some old information and writes that?

    Sorry my bad english, I'm from Finland so its not my best spoken language.
    Hope you understand our problem.


    Mikkis,

    I'm transmitting you an email around the runs. Appears to be any ram cartridge issue. Have a spare?

    Best regards,


    _Edwordstephen_
    Our Actual Exams and Pass4sure 201-01 gre exam provide you 100% pass wikipedia You can get access to The Johns Hopkins University and EXIN with multiple prep resources of ARM

  6. #6
    Join Date
    Sep 2007
    Location
    Rancho Santa Margarita, California
    Posts
    267

    Default Re: Problem with MAG pickup, and pressure pickups.

    mikkis,

    I have not heard if you were able to try downloading using a different memory cartridge.

    Please let me know when you get a chance.

    Thanks,
    Todd Paton
    todd@racepak.com
    949-709-5555 ext. 1652

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us