Page 3 of 13 FirstFirst 12345 ... LastLast
Results 21 to 30 of 129

Thread: ECU Connectors & Terminals - Holley EFI

  1. #21
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    19,280

    Default

    Quote Originally Posted by Greg Kelley View Post
    Danny, do you know the part number for the harness side 8-way Metri-Pack connector for the NTK WBO2?
    See posts #8 & #14. It's a black, eight cavity Delphi Metri-Pack 150 Series connector:
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.16)

    FYI: These Delphi Metri-Pack connectors are color coded with corresponding slots.
    If plugging into an existing connector, the color of the connector isn't a "choice".

    Is the CAN connector a Metri-Pack 150?
    Yes.
    May God's grace bless you in the Lord Jesus Christ.

    '78 BRONCO: 508" stroker, TFS heads, 11:1 comp ratio, Dominator MPFI & DIS, cold air induction, Spal dual 12" fans/aluminum radiator, dual 3" exhaust/Magnaflow mufflers, Moroso vacuum pump, Accusump, engine oil & trans fluid coolers, 100HP progressive dry direct-port NOS, A/C, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, Cage long radius arms, traction bars, 4" Skyjacker lift, 35" mud tires

  2. #22

    Default

    Danny, do you know what the terminal connector (ECU side) is on Holley 558-200 Injector Harness? What about pin-outs? Thank you in advance.

  3. #23
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    19,280

    Default

    Quote Originally Posted by BMF_RSCING View Post
    Danny, do you know what the terminal connector (ECU side) is on Holley 558-200 Injector Harness?
    The fuel injector harness connector is a gray, ten cavity Delphi Metri-Pack 150 Series connector with ten female terminals.
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.17)

    What about pin-outs?
    http://forums.holley.com/showthread....ith-Holley-EFI (Fuel Injector Harness Information)
    May God's grace bless you in the Lord Jesus Christ.

    '78 BRONCO: 508" stroker, TFS heads, 11:1 comp ratio, Dominator MPFI & DIS, cold air induction, Spal dual 12" fans/aluminum radiator, dual 3" exhaust/Magnaflow mufflers, Moroso vacuum pump, Accusump, engine oil & trans fluid coolers, 100HP progressive dry direct-port NOS, A/C, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, Cage long radius arms, traction bars, 4" Skyjacker lift, 35" mud tires

  4. #24
    Join Date
    Jul 2014
    Location
    Aptos, CA
    Posts
    87

    Default

    Does this information relate to the Terminator EFI as well? Looks like a lot of the same connectors are used. Thanks.

  5. #25
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    19,280

    Default

    Quote Originally Posted by weendoggy View Post
    Does this information relate to the Terminator EFI as well? Looks like a lot of the same connectors are used.
    Most of the connectors are the same. The Terminator has a different main harness, so some of the connectors are different.
    http://forums.holley.com/showthread....r-ECU-Question (Additional Information)
    May God's grace bless you in the Lord Jesus Christ.

    '78 BRONCO: 508" stroker, TFS heads, 11:1 comp ratio, Dominator MPFI & DIS, cold air induction, Spal dual 12" fans/aluminum radiator, dual 3" exhaust/Magnaflow mufflers, Moroso vacuum pump, Accusump, engine oil & trans fluid coolers, 100HP progressive dry direct-port NOS, A/C, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, Cage long radius arms, traction bars, 4" Skyjacker lift, 35" mud tires

  6. #26

    Default

    Quote Originally Posted by Danny Cabral View Post
    The fuel injector harness connector is a gray, ten cavity Delphi Metri-Pack 150 Series connector with ten female terminals.
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.17)
    http://forums.holley.com/showthread....ith-Holley-EFI (Fuel Injector Harness Information)
    As always Danny, thank you for your help!

  7. #27

    Default

    Using a Holley 558-104 main harness. Looking for some information on the Delphi Metri-Pack 150 series terminals.
    Interested in the Delphi part numbers, since all 150 series Metri-Pack connectors are not the same. Thanks.
    1. Looking for the air\water temperature terminals.
    2. Looking for the transducer terminals.
    3. Looking for the large male end going into the injector harness.
    Last edited by Sickfox; 09-16-2014 at 11:42 PM.

  8. #28
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    19,280

    Default

    Quote Originally Posted by Sickfox View Post
    1. Looking for the air\water temperature terminals.
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.22, 8.2 & 8.9)
    Depending on the coolant temperature sensor connector, it's either a GT Series 150 3.5 mm, or a Metri-Pack Series 150/150.2.

    2. Looking for the transducer terminals.
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 1.10)

    3. Looking for the large male end going into the injector harness.
    The fuel injector harness connector is a gray, ten cavity Delphi Metri-Pack 150 Series connector with ten female terminals.
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.17)

    Interested in the Delphi part numbers, since all 150 series Metri-Pack connectors are not the same.
    Correct, the Delphi Metri-Pack connectors are color coded with corresponding slots.
    If plugging into an existing connector, the color of the connector isn't a "choice".
    May God's grace bless you in the Lord Jesus Christ.

    '78 BRONCO: 508" stroker, TFS heads, 11:1 comp ratio, Dominator MPFI & DIS, cold air induction, Spal dual 12" fans/aluminum radiator, dual 3" exhaust/Magnaflow mufflers, Moroso vacuum pump, Accusump, engine oil & trans fluid coolers, 100HP progressive dry direct-port NOS, A/C, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, Cage long radius arms, traction bars, 4" Skyjacker lift, 35" mud tires

  9. #29

    Default

    Danny, thanks for the information.
    I looked up the Delphi information you provided, and it looks like the transducers and air/water sensors share a similar terminal.
    The Delphi part numbers for the ones I found are the following: #15326266 & #15326267. Thanks.

    However, I'm still confused about the main harness connecting to the injector harness.
    The Delphi link is not showing it. It's the pin leaving the main harness, looks like a male end.
    SICKFOX

  10. #30
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    19,280

    Default

    Quote Originally Posted by Sickfox View Post
    I looked up the Delphi information you provided, and it looks like the transducers and air/water sensors share a similar terminal.
    Yes.
    FYI: Don't confuse the GT 3.5 mm centerline terminals with the Metri-Pack 150/150.2 series terminals.
    Both are very similar "Pull-To-Seat" type terminals. Look closely at your terminals before ordering:
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Metri-Pack 150, Page 2.98)
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Metri-Pack 150.2, Page 2.22 & 2.12)
    http://www.whiteproducts.com/pull-to-seat.shtml (Delphi Metri-Pack 150/150.2 Connectors/Terminals)
    http://theelectricaldepot.com/weathe...2-pull-to-seat (Delphi Metri-Pack 150/150.2 Connectors/Terminals)
    https://www.corsa-technic.com/catego...category_id=81 (Additional Metri-Pack 150.2 Connector/Terminal Availability)
    https://www.eficonnection.com/home/c...-and-terminals (EFI Connection - Connector & Terminal Search)

    The Delphi part numbers for the ones I found are the following: #15326266 & #15326267. Thanks.
    Yes, use the 0.50-0.35 mm² terminals for the small 22 AWG transducer wiring.
    http://www.engineeringtoolbox.com/aw...uge-d_731.html (AWG to mm² Wire Conversion)

    However, I'm still confused about the main harness connecting to the injector harness.
    The Delphi link is not showing it. It's the pin leaving the main harness, looks like a male end.
    That Delphi Metri-Pack 150 male terminal (#12045773) is found on page 2.13:
    http://www.powerandsignal.com/docs/D...%20Catalog.pdf (Delphi Connection Systems Catalog - Page 2.13)
    May God's grace bless you in the Lord Jesus Christ.

    '78 BRONCO: 508" stroker, TFS heads, 11:1 comp ratio, Dominator MPFI & DIS, cold air induction, Spal dual 12" fans/aluminum radiator, dual 3" exhaust/Magnaflow mufflers, Moroso vacuum pump, Accusump, engine oil & trans fluid coolers, 100HP progressive dry direct-port NOS, A/C, LenTech Strip Terminator wide-ratio AOD/2500 RPM converter, 3:1 Atlas II, modified Dana 44/60-lockers-4.10s, hydroboost/4-disc brakes, ram-assist/heim joint steering, Cage long radius arms, traction bars, 4" Skyjacker lift, 35" mud tires

Page 3 of 13 FirstFirst 12345 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us