Results 1 to 4 of 4

Thread: Super Stock hose & fittings questions.

  1. #1

    Default Super Stock hose & fittings questions.

    Is this suitable for EFI (60 PSI)? I would assume so with the 250 PSI rating, but just wanted to be sure.
    Since there doesn't seem to be a crimp tool for the sleeve (and it doesn't even come with the fitting), I assume it is purely cosmetic? Or did I just miss the crimp tool somewhere?
    One more thing, what is your feeling on heating the hose with a heat gun to install? I had a hard time getting over the last little step on the fitting to make the sleeve tight, unless I heated it a bit.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,697

    Default

    Quote Originally Posted by Rubes View Post
    Is this suitable for EFI (60 PSI)? I would assume so with the 250 PSI rating, but just wanted to be sure.
    Yes: https://www.holley.com/products/fuel...l_system_kits/ (Holley EFI Super Stock 20' Fuel System Kits)

    Since there doesn't seem to be a crimp tool for the sleeve (and it doesn't even come with the fitting), I assume it is purely cosmetic? Or did I just miss the crimp tool somewhere?
    It's not a crimp sleeve, and it's optional: http://documents.holley.com/techlibr...e_assembly.pdf (Earl's Super Stock Hose Assembly Instructions)

    One more thing, what is your feeling on heating the hose with a heat gun to install? I had a hard time getting over the last little step on the fitting to make the sleeve tight, unless I heated it a bit.
    Use lubricating oil.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  3. #3

    Default

    Thanks Dan. So the sleeve is purely cosmetic in this case? What about these: https://www.holley.com/products/plum...arts/818406ERL. At what pressure range would you need these? Power steering lines? Transmission cooler lines?

    Then there's also this tool that states it's for "Super Stock" hose ends too: https://www.jegs.com/i/Earl's/361/D0...SABEgLy4vD_BwE. I was just confused. Thanks again.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    26,697

    Default

    Quote Originally Posted by Rubes View Post
    So the sleeve is purely cosmetic in this case?
    Yes, and it's optional.

    Yes, you can use hose clamps on Super Stock hose/ends.

    At what pressure range would you need these? Power steering lines? Transmission cooler lines?
    The Super Stock hose isn't for power steering use.
    Notice the Holley EFI Super Stock Fuel System Kits (post #2) include hose clamps.

    Then there's also this tool that states it's for "Super Stock" hose ends too: https://www.jegs.com/i/Earl's/361/D0...SABEgLy4vD_BwE
    The sleeve does not have to be crimped.
    If willing to pay $745 for that Earl's D031ERL Crimping Tool, I'd consider higher quality Earl's hose/ends that don't require a crimping tool.
    https://forums.holley.com/showthread...6686#post96686 (Holley Sniper EFI Fuel System Plumbing - Posts #2, #6, #14)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS T/W 11R 205 heads, 232°-244° duration/.623" lift/114° LSA camshaft, 12:1 C/R, TFS R-Series FTI ported intake, BBK 80mm T/B, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 200A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, -6AN fuel system plumbing, Walbro 255 LPH pump, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/3000 RPM converter, B&M Hammer shifter, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us