Results 1 to 8 of 8

Thread: Terminator EFI loses power to fuel pump.

  1. #1

    Default Terminator EFI loses power to fuel pump.

    Fuel pump loses power intermittently after warm up. No rhyme or reason as to when it goes off or comes back on.
    Last edited by herk; 04-08-2018 at 06:22 PM.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,716

    Default

    If the ECU loses the RPM signal, the fuel pump is immediately deactivated.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #3

    Default

    Ah thanks for the reply Danny. I'm totally new to the computer & EFI world, but I'm going to learn this. In fact, I'm setup for the training in Lake Havasu in May, but have a couple races before then. So with that said, where would I start looking to find a solution? Wish I hadn't been too busy or preoccupied (lazy) to install this myself, as I'm not a dumb dumb, just not real up to par on electronics, LOL.

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,716

    Default

    https://forums.holley.com/showthread...198#post101198 (Related Forum Thread)
    (Please don't type your posts like you're texting. It takes me a long time to edit it. At least use Spell Check before posting.)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  5. #5

    Default

    Thanks Danny! Sorry I'm computer illiterate, but I'll get there. I appreciate your help.

  6. #6
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,716

    Default

    You're welcome.
    If you record & analyze a short datalog of this occurrence, I think you'll see RPM Error(s) which resets the ECU and turns off the fuel pump relay.
    If you don't want to record a datalog, try viewing the RPM gauge on the 3.5" TSLCD. If RPM Errors occur, look into your distributor/ignition module, etc.

    Quick Datalogger Information:
    Always provide data, not just symptoms. Is the AFR & ignition timing optimized? Overlay the datalog onto your Global File.
    Ensure the Target A/F Ratio table is properly programmed for your engine. Ensure the ECU is "Learning" (Learn Table LINK).
    Scroll through the datalog to the problem area. Then look exactly where this happens on the Base Fuel & Timing Tables. Scrutinize:
    RPM, MAP, MAT, TPS, CTS, IAC, Target AFR, AFR Left, CL Comp, Ignition Timing, Duty Cycle, Fuel Flow, Fuel Pressure & Battery.

    Using the Holley EFI software (LINK), look at where the live cursor moves to during this occurrence, and
    manually tune that area of the Base Fuel Table (enrich or lean) & Base Timing Table (optimize ignition timing).

    I find the most helpful datalog function, is overlaying the datalog on your Global File.
    I'm in the habit of using the datalog Overlay feature every time I review a datalog.
    Click on "Datalog" (on the top Toolbar), "Activate Overlay", then "Open Data Log".
    You can literally "playback" a recorded event, and watch it as it happened on any screen.
    Minimize (shrink) the datalog window, and move it to the bottom of any Global File screen.
    Then click & scroll anywhere on the datalog, and watch it playback on your Global File (EFI software).
    http://documents.holley.com/techlibr...9r10543rev.pdf (Holley EFI Datalogger Instructions)
    https://forums.holley.com/showthread...s-amp-Datalogs (Datalog & System Log Information - Read "NOTES")
    https://www.youtube.com/watch?v=iqHO...C6FEA0BB99AF17 (How To Record & Email A Datalog)
    https://forums.holley.com/showthread...7531#post77531 (Closed Loop Datalog Tuning - Posts #2, #4 & #6)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  7. #7

    Default

    So I now have a laptop & connection cable. I'll be attempting to datalog it maybe later today, via Holley Tech support. I feel it's something simple. I just need to figure the basic computer stuff out on my end. I'll be sure to update as I learn and figure this thing out. I'm sure I'll be utilizing your advice again. Thank you.

    Danny, just curious, but if I was losing RPM signal, why would my truck run in manual mode?

  8. #8
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,716

    Default

    I don't know what you mean by "manual mode".
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us