Results 1 to 6 of 6

Thread: FE Ford Distributor for ECU Controlled Timing

  1. #1

    Default FE Ford Distributor for ECU Controlled Timing

    I'm looking into adding an HP EFI system to a 427 FE Ford engine, but I'm curious about which distributor to use that will allow me to control the ignition with the ECU.
    I've done small block Chevy setups that use the MSD electronic distributor that plugs directly into the HP EFI harness. Is there something similar for the FE Ford engines?

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,721

    Default

    Holley EFI 565-105 Dual Sync Distributor (Ford FE). It's "plug & play" and requires a CD ignition box (Instructions).

    FYI: Holley EFI now sells their own Dual Sync Hall-Effect distributors (LINK).
    They're a small cap design, "plug & play" with Holley EFI, and no need for a modified Firing Order.
    The crank & cam sensor signals also provide sequential injection capability (MPFI applications).
    It's "plug & play" (into the 10-pin ignition connector on the EFI Main Harness) and requires a CD
    ignition box (Instructions). The MSD 6201 Digital 6A CDI box & 8253 HVC-2 coil are a great match.
    The MSD CD ignition box is wired as shown in the Holley EFI Wiring Manual:
    http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual - Figure 11, Page 20)
    https://www.youtube.com/watch?v=AM7r-DauCak (Holley EFI Dual Sync Distributor - YouTube Tech Video)
    A blank cap (LINK) is available, if the user decides to convert to Coil-Near-Plug/DIS later (no CDI box).
    Of course, this component can also be used as a crank and/or cam sync/oil pump drive unit.

    The Custom Ignition Parameters (in System Parameters) for the Holley EFI Dual Sync Distributor:
    Ignition Type ............. ― "Custom"
    Crank Sensor Type ..... ― "1 Pulse/Fire"
    Sensor Type .............. ― "Digital Falling"
    Inductive Delay .......... ― "100.0 usec" ( Synchronization info, adjusted per application.)
    Ignition Reference Angle ― "50°" ( Inherent rotor-phasing of this unit.)
    Cam Sensor Type ........ ― "Single Pulse" ( "Not Used" for TBI, unless CNP ignition.)
    Sensor Type .............. ― "Digital Falling"
    Output Setup Type ..... ― "Points Output" ( CDI box ground trigger.)
    Dwell Time ................. ― "2.0 msec" ( Do not set this to 1.5 msec!)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  3. #3

    Default

    Perfect! Thanks Danny!

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,721

    Default

    You're welcome. It will also provide sequential injection capability (MPFI applications), and can be converted to Holley waste-spark DIS or Coil-Near-Plug distributorless ignition (LINK).
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

  5. #5

    Default

    Quote Originally Posted by Danny Cabral View Post
    Holley EFI 565-105 Dual Sync Distributor. It's "plug & play" and requires a CD ignition box (Instructions).
    By "plug & play", would this replace the Ford TFI module as well?

  6. #6
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    22,721

    Default

    Quote Originally Posted by redtoytruck View Post
    By "plug & play", would this replace the Ford TFI module as well?
    Of course! It plugs right into the 10-pin ignition connector on the EFI Main Harness.
    The Hall-Effect crank & cam sensors are wired as shown in the Holley EFI Wiring Manual:
    http://documents.holley.com/techlibr...10555rev17.pdf (Holley EFI Wiring Manual - Figure 11/12, Page 20/21)

    The ignition module is the first thing I got rid of. Then the distributor, CDI box & single coil was eliminated:
    http://forums.holley.com/showthread....3038#post33038 (Detailed Crank Trigger/DIS Conversion Information & Reasoning)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385" SBF, Dart SHP 8.2 block, TFS TW 11R 205 heads, 11.8:1 comp, TFS R-Series intake, Dominator MPFI & DIS, 36-1 crank trigger/1x cam sync, 160A 3G alternator, Optima Red battery, A/C, 100HP progressive dry direct-port NOS, Spal dual 12" fans/3-core Frostbite aluminum radiator, Pypes dual 2.5" exhaust/off-road X-pipe/shorty headers, S&W subframe connectors, LenTech Strip Terminator wide-ratio AOD/2800 RPM converter, M4602G aluminum driveshaft, FRPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 tires.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us