Results 1 to 5 of 5

Thread: Transducer Setup

  1. #1
    TS1092 Guest

    Default Transducer Setup

    I bought a couple 100 psi sensors part# 554-102. To set them up in the system I will be using them with I need to know the offset and gain for the sensors. I know I can figure it out, but it would be easier and probably more accurate if I had this info from the manufacturer. If any one know this info it would be appreciated. Thanks.

  2. #2
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    31,486

    Default

    The Holley EFI 554-102 sensor has a linear voltage output range of .5 - 4.5 volts (0-100 psi).
    Volts - PSI
    0.50 = 0
    0.77 = 7
    1.03 = 13
    1.30 = 20
    1.57 = 27
    1.83 = 33
    2.10 = 40
    2.37 = 47
    2.63 = 53
    2.90 = 60
    3.17 = 67
    3.43 = 73
    3.70 = 80
    3.97 = 87
    4.23 = 93
    4.50 = 100

    The Holley EFI 554-103 sensor has a linear voltage output range of .5 - 4.5 volts (0-200 psi).
    Volts - PSI
    0.50 = 0
    0.77 = 13
    1.03 = 27
    1.30 = 40
    1.57 = 53
    1.83 = 67
    2.10 = 80
    2.37 = 93
    2.63 = 107
    2.90 = 120
    3.17 = 133
    3.43 = 147
    3.70 = 160
    3.97 = 173
    4.23 = 187
    4.50 = 200
    Last edited by Danny Cabral; 03-28-2011 at 12:25 PM.
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crank & rods, forged pistons, Trick Flow T/W 11R 205 CNC comp ported heads, 12:1 comp ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI comp ported intake, BBK 80mm T/B, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal dual 12" fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio AOD, 3000 RPM C6 converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  3. #3

    Default

    Hi Danny. As you explained here for these sensors, what are the values for the Holley EFI 554-134 3.5 bar MAP sensor? Linear volts will still go up in increments of .5V, but unsure of what to put in value side? Will this also read vacuum at idle? This is for a stand-alone 7" Digital Dash setup. Thank you, Daniel

  4. #4
    Join Date
    Dec 2009
    Location
    Connecticut
    Posts
    31,486

    Default

    The Holley EFI 554-134 MAP sensor has a linear voltage output range of .5 - 4.5 volts (-14.5-35.4 psig/0-345 kPa). Yes, MAP sensors also measure vacuum.
    Volts - PSIG
    0.50 = -14.5
    0.77 = -11.2
    1.03 = -7.8
    1.30 = -4.5
    1.57 = -1.2
    1.83 = 2.1
    2.10 = 5.5
    2.37 = 8.8
    2.63 = 12.1
    2.90 = 15.4
    3.17 = 18.8
    3.43 = 22.1
    3.70 = 25.4
    3.97 = 28.7
    4.23 = 32.1
    4.50 = 35.4

    https://forums.holley.com/showthread...SI-Equivalents (MAP kPa to PSI Equivalents)
    https://forums.holley.com/showthread...4437#post64437 (MAP kPa to inHg (vacuum gauge) to PSIG)
    Holley Digital Dash: http://forums.holley.com/showthread....4985#post74985 (Read post #7.)
    May God's grace bless you in the Lord Jesus Christ.
    '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crank & rods, forged pistons, Trick Flow T/W 11R 205 CNC comp ported heads, 12:1 comp ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI comp ported intake, BBK 80mm T/B, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal dual 12" fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio AOD, 3000 RPM C6 converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

  5. #5

    Default

    Thanks Danny!
    I've put all these values in and the 554-103 comes up as 200 with Digital Dash turned on. The 554-134 says -6.1, and the factory calibrated Oil Pressure and Coolant Temperature both say HI ERR along with Fuel Level. Any idea what the issue could be? I have not started the car to see what happens. Thank you again for all your help! Cheers, Daniel

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
About us
Holley has been the undisputed leader in fuel systems for over 100 years. Holley carburetors have powered every NASCAR® Sprint® Cup team and nearly every NHRA® Pro–Stock champion for four decades. Now, Holley EFI is dominating the performance world as well as our products for GM's LS engine. Holley's products also include performance fuel pumps, intake manifolds & engine dress–up products for street performance, race and marine applications. As a single solution, or partnered with products from other Holley companies - Hooker Headers, Flowtech Headers, NOS Nitrous, Weiand, Earl's Performance Plumbing, or Diablosport - Holley products can give you the edge you need over the competition.
Join us