Several people have asked me if there were any HotKeys in the software, to make
navigation faster using a keyboard instead of having to use a mouse to navigate.
So I thought it would be useful to post on here for anybody to see.
The first set of HotKeys applies to just about any Windows based software.
If you Left Click & Hold the mouse button down, and Drag it you can Highlight several cells at once:
CTRL+C will copy those cells to the Clipboard.
CTRL+V will paste the copied items into the currently highlighted cell.
CTRL+Z will Undo an Action.
CTRL+Y will Redo an Action.
(There are limits to how many times you can use the Undo/Redo.)
Specific to the Holley EFI Software.
Right click and a small menu pops up with ways to Cut/Copy/Paste, Smooth vertical/horizontal/all values, or to Fill/Offset values.
Anytime you click on/Highlight cell values:
CTRL+Up/Down Arrows = Change by +/-1%.
CTRL+Left/Right Arrows = Change by +/-5%.
CTRL+X will Zero out the cell/highlighted area.
If you click inside the visual chart area of tables, whatever point you highlight, you can use the up & down/left & right arrows to move/adjust.
On 3D charts, the CTRL+Arrow keys works the same as when looking at the cell values.
Using ALT+[Key]
A = Acceleration Enrichment
B = Boost Setup
C = Trans Shift Parameters
D = Drive-By-Wire Settings
E = Engine Parameters
F = Base Fuel Table
G =
H =
I = Idle Parameters
J =
K =
L = Learn Table
M =
N = Nitrous Parameters
O =
P = Global File Properties/Notes
Q =
R =
S = Base Timing Table
T = Ignition Parameters/Rev Limiter settings
U =
V =
W = Water/Meth Injection Settings
X = Cranking Fuel Table
Y =
Z = Target Air/Fuel Ratio Table
Hope this helps people who like to quickly navigate, using the keyboard instead of the mouse
navigation faster using a keyboard instead of having to use a mouse to navigate.
So I thought it would be useful to post on here for anybody to see.
The first set of HotKeys applies to just about any Windows based software.
If you Left Click & Hold the mouse button down, and Drag it you can Highlight several cells at once:
CTRL+C will copy those cells to the Clipboard.
CTRL+V will paste the copied items into the currently highlighted cell.
CTRL+Z will Undo an Action.
CTRL+Y will Redo an Action.
(There are limits to how many times you can use the Undo/Redo.)
Specific to the Holley EFI Software.
Right click and a small menu pops up with ways to Cut/Copy/Paste, Smooth vertical/horizontal/all values, or to Fill/Offset values.
Anytime you click on/Highlight cell values:
CTRL+Up/Down Arrows = Change by +/-1%.
CTRL+Left/Right Arrows = Change by +/-5%.
CTRL+X will Zero out the cell/highlighted area.
If you click inside the visual chart area of tables, whatever point you highlight, you can use the up & down/left & right arrows to move/adjust.
On 3D charts, the CTRL+Arrow keys works the same as when looking at the cell values.
Using ALT+[Key]
A = Acceleration Enrichment
B = Boost Setup
C = Trans Shift Parameters
D = Drive-By-Wire Settings
E = Engine Parameters
F = Base Fuel Table
G =
H =
I = Idle Parameters
J =
K =
L = Learn Table
M =
N = Nitrous Parameters
O =
P = Global File Properties/Notes
Q =
R =
S = Base Timing Table
T = Ignition Parameters/Rev Limiter settings
U =
V =
W = Water/Meth Injection Settings
X = Cranking Fuel Table
Y =
Z = Target Air/Fuel Ratio Table
Hope this helps people who like to quickly navigate, using the keyboard instead of the mouse
Comment