Announcement

Collapse
No announcement yet.

Problem with MAG pickup, and pressure pickups.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Problem with MAG pickup, and pressure pickups.

    Hello.

    We had problems with optic pickup, on logger it goes up and down, without any reasonable meaning. I think it messed up other curves too, because rear end curve was same looking.
    I fixed that optic cable and it was ok.
    After that, it worked couple rounds nicely, until problem came back.
    Now there aint no rpm, rear end information at lastest logging.
    Exhaust temps are ok.
    We are using oil press, pump press and blower press, nozzle press aint in use.
    But at that last logging, there was information of that nozzle press too.
    Is it possible that Loggers memory dont erase everything and it finds some old information and writes that?

    Sorry my bad english, I'm from Finland so its not my best spoken language.
    Hope you understand our problem.
    TAFC/TMFC
    Woodstock Racing.

  • #2
    Re: Problem with MAG pickup, and pressure pickups.

    Hello Mikkis. Are you waiting for the red light on the memory cartridge to flash on and off multiple times? Typically, the light will turn on and then go out while the data is transferring to the cartridge. Once this process is complete, the light will flash continuously. Is there any way you could email me some of you files to the address below? Let me know if I can be of further assistance. Sincerely,
    Todd Paton
    todd@racepak.com
    949-709-5555 ext. 1652

    Comment


    • #3
      Re: Problem with MAG pickup, and pressure pickups.

      Thanks for response.
      Yes we did it like it should be done.
      Datas were OK few times, but last time it was ruined.
      I send it to you.
      TAFC/TMFC
      Woodstock Racing.

      Comment


      • #4
        Re: Problem with MAG pickup, and pressure pickups.

        Mikkis, I'm sending you an email about the runs. Looks like a memory cartridge problem. Do you have a spare? Sincerely
        Todd Paton
        todd@racepak.com
        949-709-5555 ext. 1652

        Comment


        • #5
          Re: Problem with MAG pickup, and pressure pickups.

          Originally posted by Mikkis
          Hello.

          We had problems with optic pickup, on logger it goes up and down, without any reasonable meaning. I think it messed up other curves too, because rear end curve was same looking.
          I fixed that optic cable and it was ok.
          After that, it worked couple rounds nicely, until problem came back.
          Now there aint no rpm, rear end information at lastest logging.
          Exhaust temps are ok.
          We are using oil press, pump press and blower press, nozzle press aint in use.
          But at that last logging, there was information of that nozzle press too.
          Is it possible that Loggers memory dont erase everything and it finds some old information and writes that?

          Sorry my bad english, I'm from Finland so its not my best spoken language.
          Hope you understand our problem.
          Mikkis, I'm transmitting you an email around the runs. Appears to be any ram cartridge issue. Have a spare? Best regards, _Edwordstephen_
          Our Actual Exams and Pass4sure 201-01 gre exam provide you 100% pass wikipedia You can get access to The Johns Hopkins University and EXIN with multiple prep resources of ARM

          Comment


          • #6
            Re: Problem with MAG pickup, and pressure pickups.

            Mikkis, I have not heard if you were able to try downloading using a different memory cartridge. Please let me know when you get a chance. Thanks.
            Todd Paton
            todd@racepak.com
            949-709-5555 ext. 1652

            Comment

            Working...
            X