Tweet
Kit for Mustang fitted to '88 Thunderbird Sport Coupe. Wiring diagrams were followed to the letter, setup Wizard was done correctly. Coil has power when turning over, but no power out of coil to distributor. Coil − with KOEO, shows power as it should proving the coil is good. With car turning over, no output from coil, key switched off to end start cycle the inline coil tester will flash 1-2 times.
-
-
How are your Ignition Parameters setup? Predefined selected (drop down menu) or Custom Ignition Parameters? What does your ignition system consist of? If it's a Ford TFI distributor, does it have a genuine Ford TFI ignition module? Is the Ford TFI distributor's PIP sensor OK? Is the engine block well grounded?May God's grace bless you in the Lord Jesus Christ.
'92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, Eagle forged steel crankshaft & H-beam rods, Wiseco forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA H/R camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes SS dual 2.5" exhaust, SS off-road X-pipe, SS shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires. -
Using the Wizards it is coil −. I've tried a FoMoCo OEM distributor with FoMoCo TFI and a Dyna Mod drop in with Dyna Mod TFI module. Block is grounded in all factory locations. New battery cables, all grounding areas are clean of rust, paint & dirt. Coil is OEM replacement, new plug wires and spark plugs.Comment
-
Please don't answer each & every one separately, just check them: http://forums.holley.com/showthread....5760#post45760 (Scroll down to "Typical No-Start Checks".)May God's grace bless you in the Lord Jesus Christ.
'92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, Eagle forged steel crankshaft & H-beam rods, Wiseco forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA H/R camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes SS dual 2.5" exhaust, SS off-road X-pipe, SS shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.Comment
-
I've checked the harness, checked key-on hot that it stays hot when cranking, pins to TFI harness is good, no loose pins. Coil fires after key is released.Comment
-
Ensure the Switched +12V red/white wire (pink wire - Sniper EFI) is powered in the "Run" and "Crank" key positions.May God's grace bless you in the Lord Jesus Christ.
'92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, Eagle forged steel crankshaft & H-beam rods, Wiseco forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA H/R camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes SS dual 2.5" exhaust, SS off-road X-pipe, SS shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.Comment
-
Key-on hot was not constant. Car started.Comment
-
Back again, car will fire on a few cylinders now. Have messed with computer ignition timing from 6° to 30°, TDC was established. Fuel pressure is at 55 psi with 24 lb/hr injectors. TPS Autoset was done. Firing Order is correct 13726548. Distributor has been rotated during engine cranking, still same.Comment
Comment