Announcement

Collapse
No announcement yet.

Terminator or Sniper?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Terminator or Sniper?

    I have the chance to buy a (barely) used Terminator TBI kit for $750. (Throttle body, ECU, and harness) is the old school Terminator kit better than the new Sniper system? This model does not have transmission control. Will be installing on a sbc 350. Should i purchase the used Terminator setup or a new sniper kit? I may swap to a LS later in this truck, the Terminator kit will work with an LS but the sniper will not, correct?

  • #2
    You could make both work on an LS. With the Sniper, your only option for timing control would be an external unit (for the LS) and intake manifold choices are limited to carb style intakes. The basic Terminator uses an HP ECU, which means that you could switch to MPFI if you wanted to by either buying or making your own harness.

    Comment


    • #3
      My thoughts on the LS application were using the carb intake to give it a retro look. And I have seen the harness for LS for sale. But going back to the current application (SBC 350) is there really any advantage of one over the other? I know the Sniper would eliminate the need of mounting an ECU, but I'm not too bothered by this. Is the Terminator just as reliable or more reliable than the Sniper?

      Comment


      • #4
        Originally posted by matt9327 View Post
        ...is there really any advantage of one over the other?
        http://forums.holley.com/showthread....ator-vs-Sniper (Additional Terminator vs Sniper TBI Information)

        Is the Terminator just as reliable or more reliable than the Sniper?
        I think it's more reliable, you get what you pay for.
        May God's grace bless you in the Lord Jesus Christ.
        '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

        Comment


        • #5
          So I should definitely jump for the used Terminator unit for $750?

          Comment


          • #6
            I certainly would.
            May God's grace bless you in the Lord Jesus Christ.
            '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

            Comment


            • #7
              One more question, if I wanted to later, is there an ECU I can purchase that can control an electronic transmission? This Terminator does not have transmission control currently.

              Comment


              • #8
                Yes, the Terminator/HP ECU can be upgraded to the Dominator ECU (electronic transmission control). The Sniper EFI can not.
                May God's grace bless you in the Lord Jesus Christ.
                '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

                Comment


                • #9
                  I'll jump on the Terminator EFI system then. Thank you.

                  Comment


                  • #10
                    You're welcome.
                    May God's grace bless you in the Lord Jesus Christ.
                    '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

                    Comment


                    • #11
                      Just wondering. Since the Terminator is an HP ECU, is there a way to add another WBO2 sensor to the other side of the exhaust? Sorry for hijacking the thread. LOL!
                      '69 Camaro Convertible. SBC 383 stroker by Blueprint Engines. Roller cam, 443 HP/463 TQ. Edelbrock RPM Air-Gap intake, Holley Terminator EFI, Holley Digital Dash, Hooker headers, Pypes Race-Pro mufflers, Tremec TKO-600 5 speed, 3.55:1 posi rear.

                      Comment


                      • #12
                        Only the Dominator ECU supports tuning with dual WBO2 sensors.
                        Last edited by 81 TransAm; 02-14-2019, 04:09 PM.

                        Comment


                        • #13
                          https://forums.holley.com/showthread...063#post101063 (Related Forum Thread)
                          May God's grace bless you in the Lord Jesus Christ.
                          '92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.

                          Comment

                          Working...
                          X