Tweet
Is there a test one can do with the IAC motor out of the throttle body to tell if it's good or not? I have had some cold start idle issues so I decided to pull the IAC motor to see if it looked OK. It physically looks OK, but the piston cannot be moved by hand. Is this how it should be?
-
-
Read paragraph #4: http://forums.holley.com/showthread....neral-IAC-Info (General IAC Information - Read "IAC NOTES")May God's grace bless you in the Lord Jesus Christ.
'92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires. -
Thanks Danny.Comment
-
You're welcome.May God's grace bless you in the Lord Jesus Christ.
'92 Ford Mustang GT: 385"/6.3L SBF, Dart SHP 8.2 block, forged steel crankshaft & H-beam rods, forged pistons, Trick Flow Twisted Wedge 11R 205 CNC Comp Ported heads, 12:1 compression ratio, 232°-244° duration/.623" lift/114° LSA camshaft, TFS R-Series FTI Comp Ported intake, BBK 80mm throttle body, Holley Dominator MPFI & DIS, Holley 36-1 crank trigger, MSD 1x cam sync, PA PMGR starter, PA 200A 3G alternator, Optima 34/78 Red battery, 100HP progressive dry direct-port NOS, R134a A/C, Spal Dual 12" HP 3168 CFM fans, Frostbite 3-core aluminum radiator, Pypes dual 2.5" exhaust, off-road X-pipe, shorty headers, Earl's -6AN fuel system plumbing, Walbro 255 LPH in-tank pump & Pro-M -6AN hanger, S&W subframe connectors, BMR upper & lower torque box reinforcements, LenTech Strip Terminator wide-ratio Ford AOD, 10" 3000 RPM C6 billet converter, B&M Hammer shifter, Stifflers transmission crossmember & driveshaft safety loop, FPP aluminum driveshaft, FPP 3.31 gears, Cobra Trac-Lok differential, Moser 31 spline axles, '04 Cobra 4-disc brakes, '93 Cobra booster & M/C, 5-lug Bullitt wheels & 245/45R17 M/T Street Comp tires.Comment
-
The IAC is tested by measuring the resistance of the two coils between pins A-B & C-D. To test the drivers in the ECU connect an LED test light to battery positive and with the IAC unplugged, probe each terminal of the connector harness side and the test light should flash each time the key is cycled on & off. If the light is constantly lit that tells you the wire or driver is shorted, no light would indicate an open wire or the driver has failed.Comment
-
Thanks for this.Comment
-
You're welcome Kim72.Comment
Comment